1)
Message boards :
Questions and problems :
Screen saver star globe is sporadic
(Message 102490)
Posted 8 Jan 2021 by Bobby Post: For the last 2 months now my screen saver has not been able to load the star globe graphics with the regularity I would expect from my screen saver settings. It will go away for a week at a time and come back for one day. Then it will go away for an undetermined amount of time and then it will come back for maybe 12 hours. I have checked with the boards on Einstein@Home and we cannot resolve this issue. When it happens the "show graphics" button on the tasks will be grayed out. I can load a run the star graphics program, and as I stated, it does come back once in a while. I prefer to see the star globe rather that the BOINC statistics, but since about mid November, I have not been able to consistently see the star globe. I have looked at all the settings and when it does come back it operates as per the settings I have. Any suggestions? Bobby |
2)
Message boards :
Questions and problems :
Stuck in gear
(Message 93364)
Posted 28 Oct 2019 by Bobby Post: I am back on line now after copying the cc_config.xml file that was sent to me by Jord. Thanks for all your help. Bobby |
3)
Message boards :
Questions and problems :
Stuck in gear
(Message 93363)
Posted 28 Oct 2019 by Bobby Post: Thank Jord. I don't know how the file got corrupted but this has got me back on line. I appreciate all your help. Bobby |
4)
Message boards :
Questions and problems :
Stuck in gear
(Message 93362)
Posted 28 Oct 2019 by Bobby Post: I did as instructed. The computer is now set such that the stdoutdae.txt has been reset and the values in the registry are set to the default which is zero. I noticed that the gui_rpc_auth.cfg had been changed and the password did not match the authenticator line in account_einstein.phys.uwm.edu.xml. I don't know if that would have an effect or not, but I did change the gui_rpc_auth.cfg to the original configuration file when I set up the computer to run. I am assuming that this is the password and I have no idea how it got changed. I don't read hex so I'm not sure if this is my password or not. After all this I attempted to connect with BOINC manager again and got the same result, the password is not recognized. I am at a loss right now. Bobby |
5)
Message boards :
Questions and problems :
Stuck in gear
(Message 93342)
Posted 28 Oct 2019 by Bobby Post: I did as you instructed and renamed the gui_rpc_auth.cfg file to gui_rpc_auth.old and restarted BOINC manager. It did the same thing as before where it will connect for 10 seconds and then disconnect. I assume it is filling the stdoutdae.txt file up because it has doubled in size now from ~30Mb to 72Mb. |
6)
Message boards :
Questions and problems :
Stuck in gear
(Message 93341)
Posted 28 Oct 2019 by Bobby Post: Yes I am the same. I guess my desperation is showing. I'd like to get the computer back to work, but nothing is helping right now. Thanks |
7)
Message boards :
Questions and problems :
Stuck in gear
(Message 93340)
Posted 28 Oct 2019 by Bobby Post: i'm using Window 10 on a 64 bit computer. Hope this helps. |
8)
Message boards :
Questions and problems :
Stuck in gear
(Message 93335)
Posted 27 Oct 2019 by Bobby Post: I have been using the software since reinstalling on October 7 this year. Things have been going good except last night my Internet was knocked off line. When I got up this morning, I reset my router and the Internet was back on line. I restarted my computer. I went back to BOINC manager and my project as well as 4 task I had were gone. I attempted to get back on by loading a project, but the BOINC manager cannot stay on line. It connects and then after a few seconds disconnects. I am getting a message that I am using the wrong password. I can get onto Einstein@home and my account is still active. The BOINC manager seems to be stuck in a loop and the stdoutdae.txt, now >30Mb, shows the loop that it is stuck in. I can't seem to find where to enter the correct password for the BOINC manager. Below is a sample of the loop that the program is stuck in. 27-Oct-2019 12:08:17 [---] [gui_rpc] GUI RPC reply: '<boinc_gui_rpc_reply> <handle_get_screensaver_tasks> <suspend_reason>0</suspend_reason> <result> <name>h1_0412.75_O2C02C' 27-Oct-2019 12:08:18 [---] [suspend] net_susp: no; file_xfer_susp: no; reason: unknown reason 27-Oct-2019 12:08:18 [Einstein@Home] [heartbeat] Heartbeat sent to task h1_0412.75_O2C02Cl1In0__O2MD1G2_G34731_412.90Hz_24_1 27-Oct-2019 12:08:18 [---] [poll] CLIENT_STATE::do_something(): End poll: 0 tasks active 27-Oct-2019 12:08:18 [---] [gui_rpc] GUI RPC Command = '<boinc_gui_rpc_request> <get_screensaver_tasks/> </boinc_gui_rpc_request> ' 27-Oct-2019 12:08:18 [---] [gui_rpc] GUI RPC reply: '<boinc_gui_rpc_reply> <handle_get_screensaver_tasks> <suspend_reason>0</suspend_reason> <result> Please Help |
Copyright © 2024 University of California.
Permission is granted to copy, distribute and/or modify this document
under the terms of the GNU Free Documentation License,
Version 1.2 or any later version published by the Free Software Foundation.